Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

External clutch operating lever pivot for gearbox end cover

Superceded to Guzzi ref. 2A000384

 1 in stock

 95780271 GU95780271 95 78 02 71
 9578 0271 9578.0271 95.78.02.71

Throttle cable, one ball end

We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

12607500-z 12607500 GU12607500 12 60 75 00
 1260 7500 1260.7500 12.60.75.00

Upper choke cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 1 in stock

12608300-z 12608300 GU12608300 12 60 83 00
 1260 8300 1260.8300 12.60.83.00

Throttle cable, runs from twistgrip to carb

Ball end at twistgrip

 1 in stock

13117565-z 13117565 GU13117565 13 11 75 65
 1311 7565 1311.7565 13.11.75.65

Steel intermediate clutch plate

 1 in stock

12082300-z 12082300 GU12082300 12 08 23 00
 1208 2300 1208.2300 12.08.23.00

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Crankshaft Sludge Trap Plug

 1 in stock

 12065400 GU12065400 12 06 54 00
 1206 5400 1206.5400 12.06.54.00

Valve guide

Also known as Guzzi ref. 13036800, 13036900, 13036700, 14036860, 13036801. See ENA90353 for valve guide circlips

 1 in stock

 14036860 GU14036860 14 03 68 60
 1403 6860 1403.6860 14.03.68.60